lt-qmicli [OPTION...] - Control QMI devices
Help Options:
-h, --help
Show help options
--help-all
Show all help options
--help-dms
Show Device Management Service options
--help-nas
Show Network Access Service options
--help-wds
Show Wireless Data Service options
--help-pbm
Show Phonebook Management options
--help-uim
Show User Identity Module options
--help-wms
Show Wireless Messaging Service options
--help-wda
Show Wireless Data Administrative options
--help-voice
Show Voice Service options
DMS options
--dms-get-ids
Get IDs
--dms-get-capabilities
Get capabilities
--dms-get-manufacturer
Get manufacturer
--dms-get-model
Get model
--dms-get-revision
Get revision
--dms-get-msisdn
Get MSISDN
Change PIN
--dms-uim-get-pin-status
Get PIN status
--dms-uim-get-iccid
Get ICCID
--dms-uim-get-imsi
Get IMSI
--dms-uim-get-state
Get UIM State
--dms-uim-get-ck-status=[(pn|pu|pp|pc|pf)]
Get CK Status
--dms-uim-set-ck-protection=[(pn|pu|pp|pc|pf),(disable),(key)]
Disable CK protection
--dms-uim-unblock-ck=[(pn|pu|pp|pc|pf),(key)]
Unblock CK
--dms-get-hardware-revision
Get the HW revision
--dms-get-operating-mode
Get the device operating mode
--dms-set-operating-mode=[(Operating mode)]
Set the device operating mode
--dms-get-time
Get the device time
--dms-get-prl-version
Get the PRL version
--dms-get-activation-state
Get the state of the service activation
--dms-activate-automatic=[Activation Code]
Request automatic service activation
--dms-activate-manual=[SPC,SID,MDN,MIN]
Request manual service activation
--dms-get-user-lock-state
Get the state of the user lock
--dms-set-user-lock-state=[(disable|enable),(current lock code)]
Set the state of the user lock
Restore factory defaults
--dms-validate-service-programming-code=[(Service Programming Code)]
Validate the Service Programming Code
--dms-get-band-capabilities
Get band capabilities
--dms-get-factory-sku
Get factory stock keeping unit
--dms-list-stored-images
List stored images
--dms-select-stored-image=[modem#,pri#] where # is the index
Select stored image
--dms-delete-stored-image=[modem#|pri#] where # is the index
Delete stored image
--dms-set-fcc-authentication
Set FCC authentication
--dms-get-supported-messages
Get supported messages
--dms-reset
Reset the service state
--dms-noop
Just allocate or release a DMS client. Use with `--client-no-release-cid' and/or `--client-cid'
NAS options
--nas-get-signal-strength
Get signal strength
--nas-get-signal-info
Get signal info
--nas-get-tx-rx-info=[(Radio Interface)]
Get TX/RX info
--nas-get-home-network
Get home network
--nas-get-serving-system
Get serving system
--nas-get-system-info
Get system info
--nas-force-network-search
Force network search
--nas-get-lte-cphy-ca-info
Get LTE Cphy CA Info
--nas-get-supported-messages
Get supported messages
--nas-reset
Reset the service state
--nas-noop
Just allocate or release a NAS client. Use with `--client-no-release-cid' and/or `--client-cid'
WDS options
--wds-start-network=["key=value,..."]
Start network (allowed keys: apn, 3gpp-profile, 3gpp2-profile, auth (PAP|CHAP|BOTH), username, password, autoconnect=yes)
--wds-follow-network
Follow the network status until disconnected. Use with `--wds-start-network'
--wds-stop-network=[Packet data handle] OR [disable-autoconnect]
Stop network
--wds-get-current-settings
Get current settings
--wds-get-packet-service-status
Get packet service status
--wds-get-packet-statistics
Get packet statistics
--wds-get-data-bearer-technology
Get data bearer technology
--wds-get-current-data-bearer-technology
Get current data bearer technology
--wds-get-profile-list=[3gpp|3gpp2]
Get profile list
--wds-get-default-settings=[3gpp|3gpp2]
Get default settings
--wds-get-autoconnect-settings
Get autoconnect settings
--wds-set-autoconnect-settings=[(enabled|disabled|paused)[,(roaming-allowed|home-only)]]
Get all phonebook capabilities
--pbm-noop
Just allocate or release a PBM client. Use with `--client-no-release-cid' and/or `--client-cid'
UIM options
--uim-set-pin-protection=[(PIN1|PIN2|UPIN),(disable|enable),(current PIN)]
Set PIN protection
--uim-verify-pin=[(PIN1|PIN2|UPIN),(current PIN)]
Verify PIN
--uim-unblock-pin=[(PIN1|PIN2|UPIN),(PUK),(new PIN)]
Unblock PIN
--uim-change-pin=[(PIN1|PIN2|UPIN),(old PIN),(new PIN)]
Change PIN
--uim-read-transparent=[0xNNNN,0xNNNN,...]
Read a transparent file given the file path
--uim-get-file-attributes=[0xNNNN,0xNNNN,...]
Get the attributes of a given file
--uim-get-card-status
Get card status
--uim-get-supported-messages
Get supported messages
--uim-reset
Reset the service state
--uim-noop
Just allocate or release a UIM client. Use with `--client-no-release-cid' and/or `--client-cid'
WMS options
--wms-get-supported-messages
Get supported messages
--wms-reset
Reset the service state
--wms-noop
Just allocate or release a WMS client. Use with `--client-no-release-cid' and/or `--client-cid'
WDA options
--wda-set-data-format=[raw-ip|802-3]
Set data format
--voice-get-supported-messages
Get supported messages
--voice-noop
Just allocate or release a VOICE client. Use with `--client-no-release-cid' and/or `--client-cid'
Application Options:
-d, --device=[PATH]
Specify device path
-w, --get-wwan-iface
Get the WWAN iface name associated with this control port
-e, --get-expected-data-format
Get the expected data format in the WWAN iface
-E, --set-expected-data-format=[802-3|raw-ip]
Set the expected data format in the WWAN iface
--get-service-version-info
Get service version info
--device-set-instance-id=[Instance ID]
Set instance ID
--device-open-version-info
Run version info check when opening device
--device-open-sync
Run sync operation when opening device
-p, --device-open-proxy
Request to use the 'qmi-proxy' proxy
--device-open-mbim
Open an MBIM device with EXT_QMUX support
--device-open-net=[net-802-3|net-raw-ip|net-qos-header|net-no-qos-header]
Open device with specific link protocol and QoS flags
--client-cid=[CID]
Use the given CID, don't allocate a new one
--client-no-release-cid
Do not release the CID when exiting
-v, --verbose
Run action with verbose logs, including the debug ones
--silent
Run action with no logs; not even the error/warning ones
qmicli July 2016 QMICLI(1)
Man(1) output converted with
man2html